Then it forces you to reboot or power down. Found this link explaining the problem and some options:. Has anyone else run into this? Did you try any of these options and were you successful? Yes, I have run into this This means that you need to get a card that Lenovo approved for your particular model. Frustrating and ridiculous. I am sure they did this to reduce tech support issues. I have had issues with Lenovo's Wi-Fi drivers in the past.
Look there first. Second, I assume these computers are stationary? If so, change their roaming settings in the driver to least sensitive they won't roam. Third, take a look at your Wi-Fi channel settings - if you have multiple APs deployed, has a proper channel plan been performed. Finally, I would look to interference based issues - 3rd part APs, someone running rogue detection that is being misapplied, etc. If its not explicitly allowed by the BIOS it will not work.
Yeah well I got this message on my personal machine Only I never replaced any hardware on the machine at all. I ran the Lenovo system update and apparatnly it blacklisted the card that came with the machine.
Bricked my laptop. To continue this discussion, please ask a new question. Lenovo 53, Followers - Follow Mentions Products. Kyle for Lenovo. Get answers from your peers along with millions of IT pros who visit Spiceworks. Best Answer. Lonny This person is a verified professional. Verify your account to enable IT peers to see that you are a professional.
We found 5 helpful replies in similar discussions:. Fast Answers! Jim Steinbacher May 10, Was this helpful? Thai Pepper.Goodbye Lorita, wherever you've gone Skip to content. Quick links. The problem is that this error has nothing to do with the network card, which is the stock Intel BNHMW I tried removing the card, just to see, and it boots with the same error, which points to a defective bios or something else unknown. There is no second network card, and the machine cannot be booted.
Make a ThinkPad accept any MiniPCI Card – avoid 1802 error
Obviously, since I can't get around the boot error by removing the card, the system is unbootable barring any suggestions someone here might have.
My friend is sad, and the extra sad thing is the new screen install actually worked, despite all those wonky flip squeeze in flat cable connections. The laptop was purchased novemberwhich means that the cmos battery could be dead. I'm about ready to give up on this and just get her a used new laptop, but if there is a known solution I'd appreciate learning it, thanks.
I cannot enter bios, f1 starts the process, but then it just hangs, saying: "To interupt normal startup press enter" and that's it, nothing else. I can't use a livecd for fixes since it won't boot, though the cd works and sees the livecd, then everything stops. BT could also cause that error. Try a reset of the machine: with the machine off, remove battery and charger, then press and hold down the power button for 20 seconds.
That discharges the capacitors on the motherboard. Only connect the charger and try to boot. If OK, switch off, reinsert battery and reboot again. Lovely day for a Guinness! And pigs CAN fly! I'll try the stuff that doesn't involve fully dismantling it again, but there's another option, when I discovered how cheesy that ribbon cable connection was was when I examined the ends closely under a magnifying glass and realized that they were LOOSE wires next to each other, nothing holding them in position, and some had moved, creating possible short circuit conditions, I've literally never seen anything that chintzy in a laptop, but then again I usually avoid consumer pos stuff because they suck so badly internally.
But helpful info, at this point I have to decide the value of my time versus what is realistically possible. I'll check the bluetooth stuff, I don't remember there being bluetooth in there. But thank you very much for your information. Lots of screens are still bad but here too they are improving.
Runner-ups are the L models. FYI: the 3 in T4 3 0 etc.Mini-PCI may be unfamiliar to Mac users reading this blog, just as it was to me several months ago. Think of Mini-PCI as an AirPort Extreme sized connector, but standardized such that any manufacturer can create a compatible communications card.
What a sneaky way to lock people into buying an expensive wireless card, when others can be bought for much much lower prices. The program, no Both files will require unzipping before use use the free 7-Zip or WinZip. Hopefully this will allow ThinkPad owners to use any wireless cards, and not just those offered by IBM. He also has few pages with useful technical details on this topic, as well.
Follow up to my previous hardware recognition problem. I found the problem right after my last post. Simply the wrong driver. Found an obscure link to a different driver and that fixed it. Like Like. Thanks of lot! Follow the prompt! And thanks to all the guys for keeping page up with active links! I was able to get a Intel card running on a Thinkpad T30 — recent addition to my collection!
You are commenting using your WordPress. You are commenting using your Google account. You are commenting using your Twitter account. You are commenting using your Facebook account. Notify me of new comments via email. Notify me of new posts via email. Share this: Twitter Facebook. Like this: Like Loading November 5, at pm Reply. Thank you! October 4, at am Reply. April 29, at pm Reply. July 12, at pm Reply. Any advise out there. October 6, at am Reply.Unauthorized network card is plugged in power off and remove the network card
February 10, at pm Reply. August 11, at am Reply. Worked for my renovation of an IBM A Thanks for the CD! October 23, at am Reply.
Leave a Reply Cancel reply Enter your comment here Fill in your details below or click an icon to log in:. Email required Address never made public.If an unsupported card is detected, the BIOS prints a message on the screen and stops the system:.
It may be possible to use the computer with the unauthorized card deactivated but not removed. This does not make the wireless card work, but it may allow you to boot the computer normally. This page is for Atheros-based cards and HP notebooks, but it applies to Thinkpads as well.
The second one is much simpler because it provides an already patched and compiled ipw driver required to do the job. A neighboring WWAN slot is allowed to hold such a card. On MiniPCI express! If necessary, the pin on the card can be taped over with film or painted over with nail polish to block electrical connection. Pin 20 is located on the underside of the miniPCI Express board, second pin from the notch, on the side with more pins.
Here is detailed MiniPCIe pinout. Combinations reported to work this way:. Taping over any Mini PCI-e pin is a delicate exercise in patience, the connectors are less than the width of most ball point pens. Transparent scotch type tape is easier to work with since it is possible to see where you're cutting.
See the table below for links to modified BIOS images with the whitelist disabled. The complete instructions for this procedure are here. This doesn't happen with all unauthorized cards. Therefore some newer WiFi cards use one of the signals originally meant for LEDs to implement the "radio kill" switch input. As a result, the LED doesn't get proper signals and fails. If your LED is not working, the problem could be the pin Newer cards may no longer provide the necessary negative signal there to drive the LED.
Before you apply any fixes, be sure to check the voltage between pin 11 and ground can be found for example on the MiniPCI latch arms - it should give you about 3.
The voltage between pin 13 and ground should measure about 2. The notebook has to be running while you perform the tests so be extremely careful. All the mentioned pins are on the upper side so it's quite easy to get to them with a multimeter. If all the voltages match, your LED is fixable.
The solution is to connect the ground GND to the pin However, since the new RF Silent input signal is active low, grounding the card side will tell it to turn itself off.
Therefore, we have to separate pin 13 of the card from the system board and connect ground to the system board side only. There are many ways to accomplish this. One which doesn't require any soldering is to mask pin 13 on the card with a cellophane tape and use about 3cm of thin wire to connect pin 13 of the connector to the ground. Place one end of the wire on the masked pad and insert the card into the slot.
Check if the wire is centered on the pad and try pulling it but not too hard to see if it holds. If it comes out easily, pull the card out and repeat. If you successfully attach it, you have to connect the other end to the ground. The best place is the left MiniPCI latch arm. Bend it outside and insert the wire into the small gap between the two pieces of metal the arm is made from. Finally, make sure that the wire doesn't touch anything else and doesn't stand out too much, it must not touch the touchpad electronics when you put the palmrest back on.I specifically choose that puma peak one, because i saw in the t manual that it was supported, and i'd heard of issues with unsupported cards.
System is halted What have gone wrong? And could i be because this card wasnt ordered directly from lenovo, but from some random danish vendor who had it? I've tried to google around, but without luck. Only thing i can think of trying right now is taking it out again and tripplechecking that its seated properly. Hope you guys can help me, and i hope i wont have to hack the bios whitelist or something, seeing how this network card should work without that.
Yes, this is expected. Each computer manufacturer has their own whitelist for wireless cards for standards compliance. Yeah alright. Thx for confirming. You wouldnt by any chance know more of the actual risks of flashing and using modded BIOS, vs flashing and using the regular ones, would you? Thank you for contacting Lenovo Sales Chat. My name is xxxxx Happy to help you today. I just spoke to another support rep. They again assured me there was no restriction. My T, on my desk refusing to boot with a non-Lenovo card in it, disagrees.
Fix: Unauthorized network card is plugged in – Power off and remove the card
Angry now. Very, very angry, because the store doesn't say anywhere "3G ready so long as it's a lenovo branded card ", the spec doesn't mention the restrictions on mini-pci-E cards, etc.
Since I got repeatedly misdirected by support and sales people, this is an oppurtunity to make Lenovo make this right.If after installing your new miniPCI card into your ThinkPad laptop you get an error at boot, here is the solution. Disclaimer : This worked for me, but I am unable to make any guarantee that it will work for you. I bought an Intel card, to avoid any compatibility issues. Note that this is not only based on the model number, but also some internal numbers which are different for different batches of the exact same card.
Here is a detailed explanation. The simplest solution is:. If your laptop came without a floppy drive, you may need to create or find a boot CD.
I found some free boot-CD-generating program and created a CD with an option to boot into Windows If you have Easy CD Creator, Nero, or some such software, they all let you create boot CDs, but you may need to obtain an image of a bootable floppy disk first which means you have to create the CD on another computer that does have a floppy. Categories: tech.
Do you know where i can possibly find that no You did not click the correct link.
Or, here it is again:. The site has not been pulled. Your browser may be playing tricks on you e. Firefox may try to open a. Thanks worked great on my X31 QG0. More info on the need to boot to DOS? I could not find the program I originally used to create a bootable CD. However you do it, you should be able to make it not to start Windows directly, but to boot into DOS mode.
You may need to press F8 or something while booting. I am not using that ThinkPad anymore, so I can not give you any additional details. Once you get to the command prompt, just run the no Also, does the blue Access IBM and all the wifi related Thinkpad software still work with an unauthorised card?
If you use no At least I did not need to. So no fixed that. Can somebody please provide a working like to this file, the link is now dead. Or please email it. Thank you. I have updated the link for no Con I try this hack without collateral effects?!
Thanks in advance. I am not aware of anything that works for X41 and above.So I realized that I could not connect to any wireless connection. This seemed very easy for me to solve since I was familiar with all the troubleshooting steps of the Wi-Fi adaptor. It definitely has something to do with the failure thinking in mind as it almost the last resort. I jumped into my BIOS settings and landed on the network settings, just to realize that the wireless LAN radios and wireless access port were turned off.
Who did this! Now here is the big problem. On booting, all what the screen showed was: Unauthorized network card is plugged in — power off and remove the card.
As if the error alone was not enough, the BIOS setup could not load with the error displayed, an this is where the problem became bigger. So after some research, I discovered the cause and the solutions to the problem. Even though Lenovo takes the second largest market share. This error is most common with lenovo thinkpad laptops. During the booting process, the BIOS software performs the power on self test POST which checks if the hardware components of the system are working as expected.
This includes checking the keyboard, RAM, Hard disk and all the other components. Unfortunately The Lenovo BIOS only accepts hardware manufactured by them and so it can not boot with an unauthorized adaptor plugged in. Yes, even after buying your own laptop, Lenovo still governs it with their rules. Not cool. A wireless card is a small chip located on the motherboard that gives a computer wireless capabilities.
This the safest and simplest fix for the error. With the wireless card removed, the computer boots and works normally but without the wireless capabilities.
This is better than having the error on screen all day. Open the back of the computer. You can google for your specific model and get the exact location.